Ecofys study on Crude Tall Oil markets and availability: sufficient supply for advanced biofuels, biomaterials and energy usage

UPM Biofuels commissioned a study from leading international energy and climate consultancy Ecofys – A Navigant Company, entitled “Crude tall oil low ILUC risk assessment: comparing global supply and demand”. The study looked into crude tall oil (CTO) availability, current usage, whether the feedstock creates an additional demand for land, and whether the use of CTO in advanced biofuels can cause distortive effects in the markets.

The recently conducted Ecofys study concludes that “the CTO market is not overly tight and potential surplus of about 850,000 tonnes of CTO is still available that could be tapped into”. The total potential CTO supply is around 2.6 million tonnes. Current actual CTO demand is approximately 1.75 million tonnes, of which about 1.4 million tonnes is used by distillers and roughly 230,000 tonnes for biofuels. Ecofys also concludes that “CTO use for biofuels did not cause displacement effects elsewhere, and hence CTO, a non-land using process residue, is a low ILUC (Indirect Land Use Change) risk material.”

UPM considered it necessary to investigate the impact of UPM Biofuels’ market entry, and to verify whether UPM BioVerno production may have impacted negatively on the CTO market. The study brings necessary information into the debate concerning raw material availability for various end-uses such as advanced biofuels and biomaterials.

Current debate relating to the EU’s Renewable Energy Directive puts raw material availability of feedstock into focus as most materials tend to have alternative usage. “It is important to UPM that we can showcase that our entry into the markets has had limited impacts on the overall market, while it has enabled UPM to become the key producer of wood-based biofuels and products for the biochemical industry. We believe there is tremendous innovation potential in advanced biofuels,” says Marko Janhunen, Vice President, Stakeholder Relations from UPM Biorefining.

This research was a follow-up to an earlier study from 2013 that looked into the same issues but this was before UPM began production of renewable diesel from CTO. In 2013, the study concluded that “sufficient quantities of CTO are available for biodiesel production without the risk to cause Indirect Land Use Change and that CTO should be regarded as residue”. The new Ecofys study proved that the assumptions made in the earlier report were correct and UPM has created a new value chain parallel to existing ones.

“UPM entered the advanced biofuels business in 2015 and became the world’s first producer of renewable diesel on a commercial scale from wood by tapping into our own pulp mill residue, Crude Tall Oil. Our entry has been a success, and we continue to investigate new technologies and feedstock,” Janhunen concludes.

UPM Biofuels is the only biofuel producer that has, in addition to national certification, received both RSB (Roundtable on Sustainable Biomaterials) and ISCC (International Sustainability and Carbon Certification) certifications. This is very strong proof of the sustainability of all UPM Biofuels operations.
http://www.upm.com/About-us/Newsroom/Releases/Pages/Ecofys-study-on-Crude-Tall-Oil-markets-and-availability-sufficient-supply-for-ad-001-Tue-20-Jun-2017-13-03.aspx

Related Posts

Laakirchen Papier has achieved a lasting reduction in its CO2 emissions and energy consumption

The investments of recent years have had a positive effect on both the levels of energy use and CO2 emissions at the Laakirchen paper mill. This improvement is demonstrated clearly by the Paper and Carbon Profiles, which represent the established method within the industry of showing environmental impact and provide an overview of the relevant parameters. Moreover, Laakirchen Papier AG voluntarily commissioned Quality Austria to undertake an examination of these calculations. During 2017, Laakirchen Papier completed a variety of reconstruction and extension measures, in the course of which the raw material used was switched from primary to secondary fibres. This change has contributed greatly to a reduction in the electricity requirement and CO2 emissions during the production of SC paper (product name “Grapho”) to levels that are considerably lower than those prior to the reconstruction and expansion work. Click read more below for additional detail.

Looking into our (wooden) housing future at Helsinki Design Week

Can you build a house overnight? Can it be beautiful, stylish and sustainable? The answer is yes – as the thousands of visitors to Helsinki Design Week can testify! For the fourth edition of PEFC Wood Works, PEFC Finland teamed up with architect and environmental artist Marco Casagrande to showcase the future of living to the people of Helsinki. As cities become more densely populated, we must find more agile ways to build, and live in, new housing solutions. In the center of Helsinki, PEFC Wood Works x Tikku constructed a micro-size apartment house on just one parking slot in just one night. Tikku (‘stick’) is a demonstration of dense urban housing and Finnish wooden construction. Even better, all the wood used in the installation comes from sustainably managed, PEFC-certified, forests. Click Read More below for additional information.

ANDRITZ successfully starts up biomass boiler plant at Vattenfall AB, Uppsala, Sweden

The heating plant is located on Vattenfall’s existing combined heat and power plant site in Uppsala, Sweden, some 70 km north of Stockholm. This new plant supplies more than 110 MW of district heat to the Uppsala area and is also prepared for electricity production at a later stage. The fuel for the new plant comprises different kinds of wood-based biomass, such as recycled wood, bark, wood chips, and sawdust. The ANDRITZ scope of supply included biomass receiving, handling and storage silos, a biomass-fired boiler with flue gas cleaning, and a flue gas condenser. The boiler is based on the ANDRITZ EcoFluid bubbling fluidized bed design, which combines high efficiency with excellent environmental performance. Flue gas emissions are reduced to very low levels, with the selective catalytic reduction (SCR) method for NOx emissions and a baghouse filter, including sorbent feeding, for sulfur dioxide (SO2), hydrochloric acid (HCl), heavy metals, and dust emissions. The flue gas condenser significantly increases the district heat output and, therefore, improves plant efficiency to beyond 110% when calculated using the fuel lower heating value.
Back To Top
×Close search
Search